B&B Electronics 232BSS4 Installationshandbuch

AVBPITPOS Serial Port Point-of-Sale Filtering Module Installation Manual KEMU000826 – 03/04 – Rev B

Rev. B 6 KEMU000826 03/26/04 3.1 DIP SWITCHES, CONTINUED 3.1.3 DIP SWITCH S3 Consult your POS programming manual for baud rate and other serial

Rev. B 7 KEMU000826 03/26/04 3.3 SETTING UP GILBARCO G-SITE® When setting up Gilbarco G-SITE®, follow these steps: 1. Leave S1 in the Debug mod

Rev. B 8 KEMU000826 03/26/04 SECTION 4: SOFTWARE SETUP 4.1 SETTING UP RAPID EYE SOFTWARE 1. Start the Rapid Eye Multi VIEW program and connect

Rev. B 9 KEMU000826 03/26/04 4.1 SETTING UP RAPID EYE SOFTWARE, CONTINUED 4. Expand the New Devices section by clicking on the . 5. Select Data

Rev. B 10 KEMU000826 03/26/04 4.1 SETTING UP RAPID EYE SOFTWARE, CONTINUED 6. Configure Port 1 – Data Input at: Baud Rate = 9600; Data Bits = 8;

Rev. B 11 KEMU000826 03/26/04 4.1 SETTING UP RAPID EYE SOFTWARE, CONTINUED 8. Once the device is configured, select Apply. 9. Select Yes in re

Rev. B 12 KEMU000826 03/26/04 4.1 SETTING UP RAPID EYE SOFTWARE, CONTINUED 10. After System Operational feedback is received, test the communica

Rev. B 13 KEMU000826 03/26/04 4.1 SETTING UP RAPID EYE SOFTWARE, CONTINUED 13. Once the rules are configured, select Apply then Yes in response

Rev. B 14 KEMU000826 03/26/04 4.1 SETTING UP RAPID EYE SOFTWARE, CONTINUED 15. Once installation and setup are complete and verified, replace a

Rev. B 15 KEMU000826 03/26/04 SECTION 5: TROUBLESHOOTING 5.1 DIAGNOSTIC MODE Enter the Diagnostic Mode by setting all S1 DIP switches to the OFF

Rev. B ii KEMU000826 03/26/04 ISSUE DATE REVISIONS A December 2003 Initial release. (PCN 1466) B March 2004 Added protocols and reformatted

Rev. B 16 KEMU000826 03/26/04 APPENDIX A: SYSTEM DIAGRAMS A.1 CONNECTING A POS SYSTEM WITH A SINGLE COM PORT See the figure below for a typical

Rev. B 17 KEMU000826 03/26/04 A.2 CONNECTING A POS SYSTEM WITH A SEPARATE COM PORT FOR PRINTER See the figure below for connecting a POS device

Rev. B 18 KEMU000826 03/26/04 APPENDIX B: SYSTEM DIAGRAM USING B&B SMART SWITCH B.1 CONNECTING A POS SYSTEM USING B&B SMART SWITCH AND 4

Video Systems www.honeywellvideo.com 1-800-796-CCTV © 2004 Honeywell International Inc.

Rev. B iii KEMU000826 03/26/04 EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with arrowhead symbol within an equilateral triangle is in

Rev. B iv KEMU000826 03/26/04 TABLE OF CONTENTS SECTION 1: INTRODUCTION ...

Rev. B 1 KEMU000826 03/26/04 SECTION 1: INTRODUCTION 1.1 PRODUCT DESCRIPTION Honeywell offers the technology for a truly integrated video and dat

Rev. B 2 KEMU000826 03/26/04 SECTION 2: CONTROLS AND CONNECTIONS 2.1 POS WITH A SINGLE COM PORT If the POS system has a single serial port and i

Rev. B 3 KEMU000826 03/26/04 2.2 POS WITH MULTIPLE COM PORTS If the POS system has more than one serial port, it is preferable to enable this se

Rev. B 4 KEMU000826 03/26/04 SECTION 3: CONFIGURING THE AVBPITPOS 3.1 DIP SWITCHES The AVBPIT1 is designed to interface different POS devices wit

Rev. B 5 KEMU000826 03/26/04 3.1 DIP SWITCHES, CONTINUED 3.1.1 DIP SWITCH S1 Use the S1 bank of DIP switches to select different operational mo