LDVDS-S – 2507ds - 2/2
International Headquarters: 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA
European Headquarters: Westlink Commercial Park Oranmore Co. Galway Ireland
+353 91 792444 Fax +353 91 792445
www.bb-europe.com orders@bb-europe.com support@bb-europe.com
PRODUCT INFORMATION B&B ELECTRONICS
Parameter Reporting Methods
There are four methods for parameter updates. The parameter trigger method for each parameter is configured
individually.
Time Based: The Streamer sends parameter values at a specific interval determined by the Host device.
Threshold Exceeded: The Streamer sends parameter values when a programmed threshold value is exceeded.
As Requested: The Streamer sends parameter values when requested by the Host device.
Full Speed: Parameter values are transmitted to the Host device when they are obtained from the vehicle.
Firmware Updates
The firmware program stored in flash is able to be updated through the serial port.
Accessory Cables
Accessory cabling is available (see the following B&B cable models) for the LDVDS-S to make connections to the RS-
232 Host device as well as the OBD II bus.
Model LDVDS-CBL ...........DB15 male to male J1962 OBD II, 40 in (1.0 m)
Model LDVYCBL ...............DB15 male to 2 J1962 OBD II Y-cable
Used for permanent installations to allow connection of the technician’s scan tool
Model 9PAMF6B ...............DB9 male to DB9 female cable, 6 ft (1.8 m)
Specifications
Dimensions: 4.5 x 2.5 x 1.25 in
Mounting: Two mounting tabs on enclosure
Indicators: Single red LED to indicate vehicle power & connection status
Vehicle Bus Connection: DB15 female
Pin 1 ISO9141 K/ SCI Rx
Pins 4, 5 J1850-, J1850+
Pin 6, 7, 16, 17 Ground
Pin 9 Vehicle un-switched Vbat
Pin 10 ISO9141 L
Pin 11 Vehicle Vbat to scan tool
Pin 12 CAN Low
Pin 13 CAN High/ SCI Tx
Pin 15 Low Speed GMLAN
RS-232 Connection: DB9 female, DCE
Pins 1, 4, 6 Connected together
Pin 2 RD
Pin 3 TD
Pin 5 Ground
Pin 7 RTS
Pin 8 CTS (Vehicle Ignition Status)
Pin 9 Optional Vbat Power In or Vbat power out
(2 separate build options)
Operating Temperature: -40 to 85 ºC (-40 to 185 ºF)
Operating Voltage Range: 8 to 20 VDC
Power Consumption: 1.2W in Operating Mode; 0.36W in Sleep Mode (Key Off)
Over-Voltage Protection: Survive up to 24 VDC for up to 10 minutes.
Powering Options:
Standard model powered from the vehicle through the DB-15 connector.
Build option to get input power from pin 9 of the DB-9 connector.
Build option to provide vehicle power to the host device on Pin 9 of the DB-9 connector.
Power output will be specified as 12 Watts.
Vibration Test: IEC 60068-2-6
10 sweeps of 10 to 500 to 10Hz at rate 0.5 oct/min. each axis.
Level to be 10 to 36Hz, 0.06 in DA 36 to 500Hz, 40g’s
Unit must remain operational during and after the test.
Shock Test: IEC 60068-2-27
18 to 50g’s, 11ms, ½ sine pulses, 3 each direction each axis
Unit must remain operational during and after the test.
Drop Test: IEC 60068-2-32
10 Freefall drops from 1 meter onto concrete surface.
Drop 1 time on each face (6), 1 on corner, and 1 time on each of 3 edges of that corner.
(14 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern