B&B Electronics Zlinx 485 Bedienungsanleitung PDF herunterladen

Zlinx Wireless Modbus I/O-0111ds page 1/5

International Headquarters: 815-433-5100 Fax 433-5104 www.bb-elec.com

European Headquarters: +

353 91 792444 Fax +353 91 792445

www.bb-europe.com



B&B ELECTRONICS PRODUCT INFORMATION



Zlinx Wireless I/O

Peer-to-Peer and Modbus I/O



9 Modular, Customizable Wire Replacement

9 128 / 256 Bit AES Encryption

9 Software Selectable RF Transmit Power

9 Software Selectable Over-the-air Data Rate

9 Modbus ASCII /RTU Compatible

9 Wide Operating Temperature

9 Active Repeater Functionality

9 10 to 40 VDC & 24 VAC Input Power

Zlinx™ Wireless Modbus I/O - flexible enough to fit your

applications. These plug-n-play units from B&B Electronics

combine traditional Modbus RTU remote analog and discrete I/O

with built-in wireless connectivity. Wireless RTU serves as

Modbus slave RTU in radio-based SCADA systems, or as a

peer-to-peer communication platform.

Three Ranges Available - Short, Medium, Long range.

Active Repeaters - With built-in repeater functionality on -MR

and 900 MHz -LR models, you can ensure vital signals get

through.

Modular - Just snap on your I/O and you're ready to go.

Wide Temperature - Meets most indoor or outdoor applications.

Rugged circuitry prevents signal degradation.

128 / 256 Bit AES Encryption – Secures your data.

Selectable RF Transmit Power – Allows you to optimize the

transmitter power for your application.

Selectable Over-the-air Data Rate – Allows you to decrease the

OTA Data Rate on –LR and –LR-AU versions, effectively

increasing the radio transmitter’s range.

Exception Reporting – In Modbus mode, allows the reporting of

possible problems with connected devices.

Fail Safe – Allows you to set your I/O to a safe state in the event

of a communications failure.

Calibration – Calculates correction factors to make I/O values

better match your sensor.

Communications Failure Alarm – Allows the first DO to be

configured as a COM failure alarm indicator.

Invert Output – You can invert the logic of all DO’s in peer-to-

peer mode.

Monitor – You can use the Zlinx™ Manager Software to monitor

your I/O.

Wire Replacement (Peer-to-Peer Mode)

Replicate any analog or digital signal from a remote location-

Wirelessly! Use a pair of Zlinx™ Wireless I/O modules to read

sensor inputs or control actuators in hard-top-reach locations.

Inputs and outputs of the paired Zlinx radios will mirror each

other, making it easy to add wireless I/O to any application.

Modbus Peer-to-peer or Peer to Multi-peer

Seamlessly add wireless I/O to any Modbus application.

Modbus is the most widely supported I/O protocol worldwide.

With Zlinx Wireless I/O you can now bring wireless remote I/O

into any Modbus system. Simply connect a Zlinx modem to and

RS-232 or RS-485 port of the Modbus master and it can now

poll up to 150 wireless I/O nodes – each node can be

configured for 8 to 48 I/O points.

1 2 3 4 5

Inhaltsverzeichnis

Seite 1

Seite 2 - I/O Points

Seite 3 - Specifications

Seite 4

Seite 5

Kommentare zu diesen Handbüchern

Keine Kommentare

B&B Electronics Zlinx 485 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Vernetzung B&B Electronics Zlinx 485 herunter. Zlinx Wireless I/O - Datasheet Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Vernetzung B&B Electronics Zlinx 485